Where is the throttle position sensor located on a 2006 Chevy Silverado?

right side

Likewise, where is the throttle position sensor located?

A throttle position sensor (TPS) is a sensor used to monitor the air intake of an engine. The sensor is usually located on the butterfly spindle/shaft so that it can directly monitor the position of the throttle.

Subsequently, question is, how do you reset a throttle position sensor? Turn the ignition switch on and wait 3 seconds. Immediately after the 3 seconds, the accelerator pedal must be pressed and released 5 times within 5 seconds. Wait 7 seconds and fully press the accelerator pedal and hold for approximately 20 seconds until the check engine light stops blinking and stays on.

Hereof, how do you reset the throttle position sensor on a Chevy Silverado?

The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.

What happens when your throttle position sensor goes bad?

What happens when my throttle position sensor goes bad. When a TPS goes bad, then the car's throttle body won't function properly. When the throttle gets stuck in an open position than your vehicle will receive too much air and cause it to have a high or fluctuating idle.

How do you troubleshoot a throttle position sensor?

1. Carefully unplug the electrical connector from the TPS.
2. Examine the electrical connector wires and terminals for dirt, contamination and damage.
3. Now, set your DMM to a suitable setting, like 20 Volts, on the DC voltage scale.
4. Turn the ignition key to the ON position, but don't start the engine.

What happens when throttle position sensor goes bad?

Engine won't idle smoothly, idles too slowly, or stalls If you start to experience engine misfires, stalling, or rough idling when the car is stopped, it can also be a warning sign of a failing TPS. The TPS can also send bad input that ends up stalling the engine at any time.

How do you diagnose a bad throttle position sensor?

Symptoms of a Faulty Throttle Position Sensor

1. An unexplainable bucking and jerking in the vehicle.
2. Sudden idle surges.
3. Sudden engine stalling without any apparent reason.
4. Hesitation while accelerating.
5. Sudden surges in speed while driving on the highway.
6. Intermittently flashing of check engine light for no apparent reason.

How do I reset my electronic throttle control manually?

Fully depress the accelerator pedal for 10 seconds. At this point the check engine light should change to blinking slowly indicating “Erasing ECU Memory”. 8. Release the accelerator pedal and turn the ignition switch to off.

Can you drive with a bad throttle position sensor?

If you have a bad throttle position sensor, your car will not perform well or safely. Driving with a bad throttle position sensor may also cause problems in other related systems in your car, which will mean additional repair bills.

Will a throttle position sensor throw a code?

The engine's computer has built-in logic that monitors the TPS feedback to make sure it matches up with information sent by other engine sensors. A faulty TPS can set a trouble code in the computer if the voltage value is either not present, sporadic, slow or constant, and this can illuminate your check engine light.

How do I reset my idle air control valve?

Reset the IAC valve pintle position by performing the following:

1. Depress the accelerator pedal slightly.
2. Start the engine and run for 5 seconds.
3. Turn the ignition switch to the OFF position for 10 seconds.
4. Restart the engine and check for proper idle operation.

Can you clean a throttle position sensor?

Cleaning the throttle body itself can be done using carburetor fluid and a clean cloth for the removal of light sludge. During this process, the throttle position sensor should not be cleaned due to the possibility of contamination or wire damage.

How do I reset my idle speed?

To reset the IAC valve pintle position proceed as follows:

1. Block the drive wheels, then apply the parking brake firmly.
2. Start the engine, then hold the engine speed above 2,000 rpm.
3. Turn the ignition OFF , then restart the engine and check for proper idle operation.

How do you reprogram a throttle body?

step 1: Accelerator Pedal Release Position Learning (0:15)

1. Do not depress the accelerator pedal.
2. Turn the key to the ON position for atleast 2 seconds.
3. Turn the key to the OFF position for 10 seconds.
4. Turn the key to the ON position for 2 seconds.
5. Turn the key to the OFF position for 10 seconds.

Do you have to reprogram a throttle body?

Hi there. After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset. The engine light will go out and clear all codes as it goes into a learn cycle.

Can throttle position sensor affect transmission shifting?

The Throttle Position sensor measures the throttle position, which is controlled by the gas pedal. It is used to determine engine load and if it fails it can cause automatic transmission shifting problems.

Can a dirty throttle body cause transmission problems?

Car acceleration problems can feel like transmission troubles as well. The cause may not be the transmission and instead could be the result of air or fuel distribution issues or faulty sensors. Air distribution troubles such as a dirty throttle body inhibit airflow, resulting in a poorly powered engine.

How do you change a throttle position sensor on a Chevy?

Remove the throttle position sensor from the throttle body on the intake manifold assembly. Install the new sensor to the throttle body on the intake manifold. Check the threads on the bolts and use a small wire brush to clean them as needed. Set the sensor bolts in position and tighten them by hand.

How do you clean a throttle body?

Follow the plastic duct from the air filter housing up to the throttle body. Remove the duct and locate the throttle cables and rotating mechanism. Rotate the throttle mechanism and spray the cleaning solvent around the inside of the throttle body. Give it a moment to work and then wipe out the crud.

What causes a p0122 code?

P0122 Code: Meaning, Symptoms, Causes, Diagnostics, and Fixes. The P0122 code triggers when the “A” circuit on your vehicle's throttle position sensor is giving too low of an input voltage. This sensor is used by your engine control module to track the position of the throttle.

Why does the throttle position sensor Get Low Voltage?

A P0122 code means that the the vehicle's computer has detected that the TPS (throttle position sensor) "A" is reporting too low a voltage. On some vehicles that lower limit is 0.17 - 0.20 volts (V). In simple terms, the throttle position sensor is used to determine what position the throttle is at.