Passive-interface command is used in all routing protocols to disable sending updates out from a specific interface. However the command behavior varies from one protocol to another. This simply means that the router will still be able to receive updates on that passive interface and use them in the routing table.
Keeping this in consideration, what is the purpose of the passive interface command?
The passive interface Command With EIGRP running on a network, the passive-interface command stops both outgoing and incoming routing updates, since the effect of the command causes the router to stop sending and receiving hello packets over an interface.
Also, how do I turn off passive interface? Disable the RIP Passive Interface
- On switch 1, enter the configuration mode for the router. SEFOS# configure terminal SEFOS(config)# router rip SEFOS(config-router)# network 10.0.0.1.
- Disable the passive interface status for VLAN 1.
- Review the RIP interface for the periodic updates sent over the interface.
Likewise, how do you set up a passive interface?
How to Configure Default Passive Interfaces
- enable.
- configure terminal.
- router eigrp { autonomous-system-number | virtual-instance-number }
- passive-interface [default ] [ type number ]
- no passive-interface [default ] [ type number ]
- network network-address [ options ]
- end.
- show ip eigrp interfaces.
What does passive interface mean OSPF?
If an interface is configured as a passive interface, it does not participate in OSPF and does not establish adjacencies or send routing updates. However, the interface is announced as part of the routing network.
What happens when you configure the passive interface command on a RIP interface?
Passive Interfaces. Starts the RIP routing process. Sets the interface as passive, meaning that routing updates will not be sent out this interface. NOTE: For RIP, the passive-inter-face command will prevent the inter-face from sending out routing updates but will allow the interface to receive updates.What are two common types of static routes in routing tables choose two?
There are two common types of static routes in a routing table, namely, a static route to a specific network and a default static route. A static route configured on a router can be distributed by the router to other neighboring routers.What is Eigrp Cisco?
Enhanced Interior Gateway Routing Protocol (EIGRP) is an advanced distance-vector routing protocol that is used on a computer network for automating routing decisions and configuration. The protocol was designed by Cisco Systems as a proprietary protocol, available only on Cisco routers.How does Eigrp show passive interface?
To configure an interface as a passive interface in EIGRP, you'll use the passive-interface interface#/# command in EIGRP router configuration mode. To verify rather or not an interface is in passive-mode you can use the show ip protocols command in privileged mode.What are two functions of dynamic routing protocols choose two?
Dynamic routing protocols exist to discover the network, maintain routing tables, and calculate the best path. Having low levels of routing overhead, using the path specified by the administrator, and avoiding the exposure of network information are functions of static routing.What is one function of a Layer 2 switch?
Layer 2 switching (or Data Link layer switching) is the process of using devices' MAC addresses on a LAN to segment a network. Switches and bridges are used for Layer 2 switching. They break up one large collision domain into multiple smaller ones. In a typical LAN, all hosts are connected to one central device.What is the purpose of the passive interface command quizlet?
What is the purpose of the passive-interface command? Answer: allows a router to receive routing updates on an interface but not send updates via that interface. Refer to the exhibit.What is default information originate?
default-information originate (OSPF) To generate a default external route into an Open Shortest Path First (OSPF) routing domain, use the default-information originate command.What are some advantages with using Eigrp as the routing protocol in your network?
Other EIGRP advantages include: Easy transition to IPv6 with multi-address family support for both IPv4 and IPv6 networks. Superior scaling of Interior Gateway Protocol (IGP) for large dynamic multipoint (DM) VPN deployments. Very fast rapid convergence times for changes in the network topology.What is the metric that is used by OSPF?
What is the metric that is used by OSPF? OSPF uses cost as a metric. OSPF calculates cost inversely to the bandwidth of an interface. The higher the interface bandwidth, the lower the cost of the interface.What are two reasons that will prevent two routers from forming an OSPFv2 adjacency choose two?
What are two reasons that will prevent two routers from forming an OSPFv2 adjacency? ( Choose two.)- a mismatched Cisco IOS version that is used.
- mismatched OSPF Hello or Dead timers.
- mismatched subnet masks on the link interfaces.
- use of private IP addresses on the link interfaces.
