Standard / Metric Wrench Conversion Chart
| Bolt Diameter | Standard | Metric |
| 3/16" | 3/8" | 10mm |
| 1/4" | 7/16" | 11mm |
| 5/16" | 1/2" | 13mm |
| 3/8" | 9/16" | 14mm |
Consequently, what is the equivalent of a 15mm socket?
Wrench Size Chart for Bolts
| Bolt Diameter | Wrench Size (Standard) | Wrench Size (Metric) |
| 3/8" | 9/16" | 15mm |
| 7/16" | 5/8" | 16mm |
| 1/2" | 3/4" | 19mm |
| 9/16" | 13/16" | 21mm |
Also Know, what is equivalent to a 12mm socket? Wrench Conversion
| . Wrench Conversion Table Equivalent Sizes |
| Differ-ence in 1/1000s of an inch | Size in Inches | Compares Standard and Metric wrench sizes (where they CLOSELY match, and where they don't - wrench equivalence) |
| 3.69 | 0.46875 | Close enough 15/32 and 12mm |
| 28 | 0.47244 |
| 12 | 0.50000 |
Beside above, what is 14mm in standard?
13mm. Little over 1/2 Inch. 0.51181 Inches. 14mm. 9/16 Inch.
What is equal to a 13mm socket?
' Well, 13mm equates to 0.512 inch so a 1/2" would be tight, but 19mm is a better equivalent at 0.748". There is definitely a difference between a 13mm and a 1/2" wrench/socket.
How many mm is 3/8 inch?
Fractional Inches to Decimal Inches and Metric Millimeters
| Inches | Metric |
| Fractional | Decimal | mm |
| . | 0.3740 | 9.5000 |
| 3/8 | 0.3750 | 9.5250 |
| 25/64 | 0.3906 | 9.9219 |
What size socket is a spark plug?
You'll need just a few tools to change out the spark plugs on your car. The most important tool is a socket wrench with an extension and a spark plug socket. Spark plug sockets come in two sizes: 5/8 inches and 13/16 inches. Most spark plug sockets have a rubber insert that holds the plug snugly in place.What size bolt fits a 14mm socket?
Size Chart
| Bolt size | Size | Tolerance |
| 5/16"UNF | 1/2" | 13.00 |
| M8 | 13mm | 13.30 |
| 1/4"BSW | 13.64 |
| 14mm | 14.35 |
What's the next size up from 1 2?
Ear Gauge to MM Conversion Table
| Gauge | Millimeters(mm) | Inches |
| 00g | 10 mm | 3/8" |
| 11 mm | 7/16" |
| 12 mm | 1/2" |
| 14 mm | 9/16" |
Is 10mm bigger than 3 8?
It's the same size. 3/8 is in inch and and its 10mm.What is a 30 mm socket in standard size?
Wrench Size And Conversion Table
| Inches | Millimeters | Spanner |
| 1.063 | 27mm | 1 1/16 AF; 27mm |
| 1.100 | 5/16 Wworth; 11/16 BSF |
| 1.125 | 1 1/8 AF |
| 1.181 | 30mm | 30mm |
What are the standard socket sizes smallest to largest?
Metric Socket Sizes Chart
| 1/4" Drive | 3/8" Drive | 1" Drive |
| 10mm | 13mm | 60mm |
| 11mm | 14mm | 63mm |
| 12mm | 15mm | 65mm |
| 13mm | 16mm | 67mm |
What size is a 36mm socket in standard?
36mm = 1.5 inch socket?Is 5mm the same as 1/4 inch?
4mm = 5/32 inch (= a bit over 1/8 inch) 5mm = just over 3/16 inch. 6mm = almost 1/4 inch.How big is a mm on a ruler?
Rulers are often 30 centimeters long, which are designated by large numbers on the ruler. Between each centimeter (cm) mark, there should be 10 smaller marks called millimeters (mm).How many 32nds are in an inch?
| mm to Inch Conversion Chart |
| mm | Inches (approximate) |
| 16 | 5/8 | 20/32 |
| 17 | 11/16 | 21/32 |
| 18 | 11/16 | 23/32 |
How thick is 2mm in inches?
Millimeters to inches conversion table
| Millimeters (mm) | Inches (") (decimal) | Inches (") (fraction) |
| 1 mm | 0.0394 ″ | 3/64 ″ |
| 2 mm | 0.0787 ″ | 5/64 ″ |
| 3 mm | 0.1181 ″ | 1/8 ″ |
| 4 mm | 0.1575 ″ | 5/32 ″ |
What does a millimeter look like on a ruler?
On a metric ruler, the numbers represent centimeters. The individual lines between the numbers represent millimeters. Each millimeter is one-tenth of a centimeter, so ten millimeters equals one centimeter. Before you start measuring, make sure that one end of the object is lined up with the 0 cm mark on the ruler.How many mm means 1 inch?
25.4mm
What is a 22mm socket in standard?
22mm socket equals: a 22mm socket approximately equals 7/8". 7/8" is just a hair larger (. 875 vs . 866) but should not round the bolt as long as you keep the socket 'square' to the bolt.How do you measure bolt size?
To measure the diameter of screws and bolts, you measure the distance from the outer thread on one side to the outer thread on the other side. This is called the major diameter and will usually be the proper size of the bolt.What size is an inch?
One inch (2.5 cm) is roughly the measurement from the top knuckle on your thumb to your thumb tip. Measure yours to see how close it is to 1 inch. 
