How do you test a hunter XC sprinkler system?

To initiate the test program:

1. Press and hold the PRG button. The station number will be flashing.
2. Press the or button to scroll to the station you would like the test program to start with. Use the and buttons to set a run time of up to 15 minutes.
3. After a 2 second pause, the test program will begin.

Simply so, how do I turn on my Hunter XC sprinkler system?

X-Core - Manually Run a Single Station

1. Turn dial to MANUAL – ONE STATION position.
2. Station run time will flash in the display.
3. Turn the dial clockwise to the RUN position to run the station (only the designated station will water, then the controller will return to automatic mode with no change to the previously set program).

Likewise, why does my sprinkler system keep running? There are two reasons why your sprinklers would continue running: It's possible your valves have been opened manually. You'll need to locate your valve box(es) and turn the solenoid(s) clockwise until snug. The solenoid is located on the top of the valve and looks like a cylinder with two wires protruding out of it.

Also to know, how do you program a hunter sprinkler system?

X-Core - Programming Start Times

1. Turn the dial to the START TIMES position.
2. The factory preset is set on program A. If necessary, you can select program b, or C by pressing the PRG button.
3. Use the plus (+) or minus (-) button to change the start time.
4. Press the arrow (>) button to add an additional start time, or PRG button for the next program.

How do I manually start Hunter Pro C?

Pro-C - One Touch Manual Start and Advance

1. With the dial in the RUN position, hold down the button for 2 seconds.
2. This feature automatically defaults to program A. You can select program B, or C by pressing the PRG program.
3. The station number will be flashing.
4. Press the button to scroll to the station you wish to begin with.

How long do I run my sprinkler system?

Run your sprinkler and see how long it takes to get a half inch of water in the can – just like a rain gauge. Usually it's about 30 minutes. So 20 minutes, 3 times per week will get an inch of water on your lawn, and 30 minutes 3 times per week will get 1 ½” down.

What does no AC mean on a sprinkler system?

The "NO AC" display is a diagnostic message telling you that the controller has stopped receiving AC power. The controller is running on the power supplied by the backup battery. Check the power source by plugging a lamp or radio into the wall outlet to verify there is power at the outlet.

Why is my sprinkler not turning on?

The most common cause of individual sprinklers not coming on is blockage. The thin spray opening of a sprinkler head easily becomes clogged with dirt and debris. Inspect malfunctioning sprinkler heads while the water supply is off, and clear blockages with a thin, straight-edged tool such as a screwdriver.

How do I restart my sprinkler system?

Slowly open the main shutoff valve to let water into the sprinkler system. For a ball valve, turn the lever handle one-quarter turn until the handle is parallel to the pipe; this is the fully open position. For an in-ground shutoff valve, use a sprinkler valve key to turn the valve counterclockwise until it stops.

What causes a sprinkler valve to stay open?

Air Trapped in the Valve: A small bubble of air becomes trapped in the tiny water ports of the valve, this stops the water from flowing through the port. Since the water flowing through the port is what holds the valve diaphragm closed, the valve stays open.

How do you test a sprinkler solenoid valve?

How to Test Sprinkler Solenoids

1. Turn off the water supply. Open the bonnet of the sprinkler valve and unscrew the solenoid, taking care that you don't drop the plunger and the spring.
2. Open the solenoid housing and inspect the plunger.
3. Reinsert the solenoid plunger into the housing.
4. Turn on the water and test the sprinkler.

How do you drain a hunter sprinkler system?

How to Winterize a Hunter Sprinkler System

1. Locate the main water shutoff valves inside your home and turn them off by laying the ball valve lever perpendicular to the main water line.
2. Locate the main drain valve, which is close to or on the main line shutoff valve, and place a bucket beneath it.

How do you fix a stuck sprinkler valve?

How to Repair a Stuck Sprinkler Valve

1. Step 1 – Turn the Water Off. Make sure to turn the water supply off to prevent any water pressure build up which can damage your sprinkler system.
2. Step 2 – Find the Valve. A valve looks like a thin cylinder with a wire at each end.
3. Step 3 – Clean the Diaphragm.
4. Step 4 – Reassemble the Sprinkler Valve.

How do I find my sprinkler zone valve?

Start at that sprinkler and try to find the valve nearby. The cheapest and easiest way to find buried irrigation valves is often to probe the soil with a thin rod, such as a long screwdriver. Often you can estimate the rough location of the irrigation valve, then find a buried valve box by probing the ground.

How do you open a solenoid valve manually?

One way is to simply turn the solenoid (the black cylinder with 2 wires) counter-clockwise a 1/4 to 1/2 turn. To shut off the valve, twist the solenoid clockwise until it is snug on the valve. The other way is to use the bleed screw the same way, loosen the screw enough to realease air (1/4 to 1/2 turn).