Roof drip edge flashing corner detail Install roof drip edge along the eaves, add underlayment, then place drip edge along the gable end. The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.Likewise, do you nail drip edge?
Nail the drip edge to the roof deck with minimum 12-gage roofing nails spaced 8 to 10-inches on center and 1-½ to 3-inches from the edge of the sheathing. Adjacent drip edge pieces should be lapped minimum 2 inches. Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch.
Subsequently, question is, how important is drip edge? What is Drip Edge & Why It's Important. Drip edge is the flashing that protects the edges of your roof, both the eaves and the gable ends. This is great because it protects the wood structure underneath your roofing shingles, an area of the roof you can't see … but one that's prone to water damage and wood rot.
Also to know, how do you apply drip edge?
Install roof drip edge along the eaves, add underlayment, then place drip edge along the gable end. The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.
Does drip edge go over or under felt?
1 Answer. It depends on where the drip edge is. At the side, or gabels, of a roof, the drip edge goes over the roofing felt. At the bottom of the roof, the drip edge goes under the roofing felt.
Does drip edge go under tar paper?
The drip edge should be over the paper at the eaves, and under along the rake. mroberson: Its a TRAP! Back in my construction days, I learned that you place the tar paper OVER the drip edge on the eaves so if moisture gets through the shingles, it does not get under the drip edge.Do you install gutters under drip edge?
If your gutter has been previously installed, rather than taking it down and redoing it, you can easily place a small strip of metal flashing under the drip edge and over the back of the gutter (as shown by the illustration at the bottom of this page) so the water will shed into the gutter.Is a drip edge necessary?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.How far should shingles overhang drip edge?
The edge of the shingles should hang over a roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if drip edge flashing is installed. Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards.Is drip edge needed with metal roofing?
Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. It is non-corrosive and non-staining so that your roof looks good but is structurally stable.How much drip edge do I need?
I usually select drip edges with at least a 4-inch roof leg along the eaves edge and a 2-inch leg along rakes. The code calls for the fascia/rake leg to extend 1/4 inch below the roof sheathing and the Fortified Home guides call for 1/2 inch. But I like to use drip edge with at least a 1-inch fascia/rake leg.What color drip edge should I use?
The most common colors for drip edge are white and brown. However, some roofing companies can provide color match drip edge. The color is often chosen to match the shingles or the gutters to create a seamless look. The color can also be chosen to match the shutters or trim of the house and act as an accent color.What is the difference between drip edge and rake edge?
Drip edge and rake edge are the first parts of the roof system to be installed. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends. They both look very similar and are often not differentiated in name by some suppliers and simply called drip edge.Should drip edge be tight to fascia?
The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails. If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit.Can you install drip edge on existing roof?
Replacing Drip Edge Eave Strips: Install the eave strips on the lower roof edges first, with the eave strips under the shingles and felt underlayment. Align one end of the lower eave strip even with the edge of the roof decking. Lift up roof shingles, and nail the eave strip in place with galvanized roofing nails.Which side of roofing felt goes down?
When laying sheets of tar paper, always lay the sticky, glossy side down. Tar paper's two sides are noticeably different. One side is somewhat sticky, though don't expect it to leave a glue-like residue on your hands. The other side is smooth like paper, and typically contains lettering and line markings.How much does drip edge cost?
Drip Edges – Inspect and replace drip edges as necessary. Drip edges are added to the roof to direct water into the gutters. They cost about $1-$2 per linear foot installed. Other Damage – Have a professional inspect your eaves for damage before repairing fascia and soffits.Do you put drip edge on gable ends?
Drip edge or eave strip is the strip of metal flashing that runs under your shingles along the front side of the eaves of your house. Drip edge can also be installed on the gables/rakes of your home as well.Do you have to replace drip edge when replacing roof?
Drip edge comes in 10-foot strips and attaches to the roof deck before the roofing felt goes on. Unless the old drip edge is in like-new condition, replace it.Why does water leak behind my gutters?
If the gutters are clogged, it's possible that the water is overflowing the gutters and this is contributing to the leak. Water should run out the downspout and away from the house without filling the gutter. If the water fills the inside of the gutter, this means the gutters are clogged.How do you install drip edge on peak?
Cut the top of the flashing at a slight angle to the face of the rake, and bend the vertical leg back against the rake trim. 2. Hold a piece of rake flashing in place, and then mark and cut its leading edge plumb to the eave fascia. To hide the folded section of the eave cut, trim its bottom edge.What is a drip edge flashing?
Drip edge is a roof flashing that is installed at the leading edge of your shingle near the gutter It generally is a 1”x 3” or 1”x 2” piece of metal flashing slipped under the roofing material and over the top of the paper felting underneath the roofing shingles that hangs down into the gutter approximately 1” 
