How do you change the coil on a Poulan chainsaw?

This article provides step-by-step instructions for replacing the ignition coil on a Poulan chainsaw.

1. Let's get started.
2. Remove the starter assembly.
3. Disconnect the ignition coil.
4. Remove the harness clip.
5. Remove the ignition coil.
6. INSTALLING THE NEW IGNITION COIL [top] 6.
7. Set the ignition air gap.
8. Secure the wires.

Accordingly, how do you test a coil on a Poulan chainsaw?

Pull the start rope on the chainsaw and watch the end of the plug as you do. If you observe a spark jumping between the tips of the spark plug gap, it means the chainsaw coil is good. If there is no spark, it means the chainsaw coil will need to be replaced.

Secondly, how do you change a spark plug on a Poulan chainsaw? How to Replace the Spark Plug on a Poulan Chainsaw (Model P3314)

1. Remove the (3) screws securing the top cover to the saw.
2. Remove the spark plug boot.
3. Use a spark plug wrench (or socket) to loosen the spark plug.
4. Remove the spark plug from the cylinder.
5. The "gap" is the distance between the ground electrode (metal strap) and the center electrode.

Keeping this in consideration, how does an ignition coil work on a chainsaw?

Electrical currents run through the ignition coil and transmit electricity to the spark plug. The electricity creates sparks within the spark plug, and the sparks ignite the fuel in the engine, enabling the chain saw to run. Testing the ignition coil at home is simple to do and requires minimal tools.

Can you rebuild an ignition coil?

If the electrical coil is physically damaged, you have to replace it. On the other hand, if the electrical coil is physically intact, it may still work well after a repair so get your tools ready to rewind the coil.

What is the spark plug gap for a Poulan chainsaw?

.025-inch

How do you check a coil?

The only safe way to test for spark is to use a spark plug tester tool. If a coil problem is suspected, measure the coil's primary and secondary resistance with an ohmmeter. If either is out of specifications, the coil needs to be replaced. A coil can be easily bench tested with a digital 10 megaohm impedance ohmmeter.

How do I know if my chainsaw coil is bad?

Here are some of the most common symptoms of bad ignition coil.

1. #1 – Backfiring.
2. #2 – Poor Fuel Economy.
3. #3 – Engine Misfiring.
4. #4 – Vehicle Stalling.
5. #5 – Engine Jerking, Rough idling, Poor Power.
6. #6 – Check Engine Light On / DTC Code.
7. #7 – Engine Hard Starting.
8. CNP Coil Type.

How do you test a condenser?

How to Test a Condenser in a Small Engine

1. Remove the condenser from the engine.
2. Switch the volt ohmmeter to the ohms position.
3. Touch the red lead to the hot connector on the condenser.
4. Remove the leads and reverse the placement to the condenser.
5. Movement from the meter's needle indicates the condenser is good.

Why is my chainsaw not getting spark?

If there is a spark during this process, there is a problem with the spark plug and not the ignition coil. If there is no spark during this process, the problem is most likely a defective ignition coil. Remove the screws that hold the outer housing of the chain saw in place.

How do you test a magneto coil?

Pull the rubber casing off the spark plug. Set the multimeter into the ohms function, or just use an ohmmeter. Manually set the dial or button on the meter to the 40 k range. Do not use auto ranging, as it is unreliable with a magneto.

Can a chainsaw Flywheel go bad?

The magnets as North and South on a Flywheel. They are usually even labeled, at least in most Stihls. If they are no longer N/S, even if they have magnetism, they won't make a spark. So yes, it can occur.

How does a magneto work?

The principle behind a magneto is the exact opposite of an electromagnet. Whereas an electromagnet uses electricity passing through a coil to produce a magnet, a magneto uses a magnetic field in the vicinity of a coil, called the armature, to produce an electric current.

How do you tune up a chainsaw?

How to Tune and Maintain a Chainsaw

1. Remove the chain brake cover. Remove the nuts that hold the brake cover to your saw.
2. Remove the chain and bar.
3. Clean out the chain brake.
4. Wipe down the whole chainsaw.
5. Remove the top cover.
6. Replace air filter.
7. Replace fuel filter.
8. Sharpen the chain.

Does a chainsaw have a spark plug?

The Role of the Spark Plug The spark plug in a Stihl chainsaw engine -- or in any engine -- is a simple device. The spark ignites the fuel/air mixture in the combustion chamber, and the explosion drives the piston and makes the engine work.

Are all chainsaw spark plugs the same?

Spark plugs are a key part of maintaining a petrol power tool, especially STIHL chainsaws, and you may think that one spark plug is much the same as another. A standard NGK spark plug and NGK spark plugs sold by STIHL may have the same part number stamped on them, but the STIHL NGK spark plug has some key differences.

What is the spark plug gap for a Craftsman chainsaw?

.025"

What type of gas does a Poulan Pro use?

Poulan Pro's products use 87 octane regular unleaded gasoline in their two-cycle and four-cycle engines. Choose one that contains no more than 10 percen alcohol, and never use a diesel or E85 fuel because it will ruin the engine. Fresh gasoline mixes best with oil.