The correct placement of a roof drip edge is on top of the roof's exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
Likewise, people ask, how far should drip edge be from fascia?
Code requires that the drip edge extend at least 2 inches onto the roof from the fascia board. This drip edge extends much farther. Nailing along the eaves should be spaced at no more than 12 inches on-center.
Also Know, should you use drip edge touch fascia? The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails. If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit.
Thereof, does drip edge go over fascia?
If the home has no gutter, the drip edge will prevent the water from running down the fascia and onto or into the soffit cavity. However, without the drip edge, the water sticks to shingles, potentially working its way under the shingles to cause a leak.
Does drip edge go under or over tar paper?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
How do you remove fascia from drip edge?
Removing Drip Edge Eave Strips:- Gently lift up the shingles along the lower edge of the roof, and find the nails attaching the eave strip to the roof decking.
- Use a flat pry bar and hammer to remove the nails holding the eave strip to the roof decking.
- Slip the eave strip out from under the shingles.
Do roofers replace fascia?
Your fascia boards are typically replaced at the same time as your gutters, or sometimes with roof replacement. More commonly, you'll only have to make repairs where damage has occurred.Should rain gutters be installed under drip edge?
A permanent solution you should consider is installing drip edge. Drip edge gets installed under the first course of shingles and promotes water to run freely from roof edge down into gutter. Without it, water may run down behind your gutter, down fascia board and siding, leading to potential damage.Do rain gutters go under drip edge?
If your gutter has been previously installed, rather than taking it down and redoing it, you can easily place a small strip of metal flashing under the drip edge and over the back of the gutter (as shown by the illustration at the bottom of this page) so the water will shed into the gutter.What color drip edge should I use?
The most common colors for drip edge are white and brown. However, some roofing companies can provide color match drip edge. The color is often chosen to match the shingles or the gutters to create a seamless look. The color can also be chosen to match the shutters or trim of the house and act as an accent color.Can drip edge be painted?
Yes you can paint the aluminum drip edge and it hold up very well. Just be sure it is clean and paint it with a good exterior acrylic primer and finish with a exterior acrylic semi-gloss house paint.How far should shingles overhang drip edge?
The edge of the shingles should hang over a roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if drip edge flashing is installed. Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards.Which side of roofing felt goes down?
When laying sheets of tar paper, always lay the sticky, glossy side down. Tar paper's two sides are noticeably different. One side is somewhat sticky, though don't expect it to leave a glue-like residue on your hands. The other side is smooth like paper, and typically contains lettering and line markings.What is the difference between drip edge and rake edge?
Drip edge and rake edge are the first parts of the roof system to be installed. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends. They both look very similar and are often not differentiated in name by some suppliers and simply called drip edge.What is the best material for fascia boards?
Cedar is a popular fascia wood and redwood is another. That's because both species resist rot and moisture very well, even when unpainted. If you prime and paint the fascia, you can also make them out of fir, spruce or pine, which are all less expensive. You construct fascia boards out of 1-inch lumber.Do you have to replace drip edge when replacing roof?
Drip edge comes in 10-foot strips and attaches to the roof deck before the roofing felt goes on. Unless the old drip edge is in like-new condition, replace it.Is drip edge needed with metal roofing?
Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. It is non-corrosive and non-staining so that your roof looks good but is structurally stable.How thick should fascia boards be?
Replacement fascias do vary in thickness by manufacturer, but the rule of thumb is that to qualify structurally as a replacement board they should be somewhere between 16mm and 25mm thick - our most common range is the 18mm Replacement Fascia.How do I protect my fascia board?
Your fascia boards bridge the gap between your roof and your gutter.Taking Care of Your Fascia Boards
- Make sure that you choose excellent products.
- Use galvanized nails.
- Don't nail them in a way that will split the board over time.
- Paint them when possible, or add wood hardener.
