Floors. Both 1/4- and1/2-inch cement board are appropriate for floors. To install cement board on floors, cement board manufacturers mandate a 5/8-inch plywood subfloor or OSB underlayment.Similarly, it is asked, can you use Hardie board on floors?
On existing floors: HardieBacker® cement board may be installed under or over Vinyl Composition Tile (VCT) and other resilient flooring.
Likewise, do you have to put Thinset under cement board? Thinset is absolutely required beneath backer-board on a floor. Also, backer-board provides no structural strength at all. You can not install it directly over a 1x subfloor; that is way too thin and will deflect. It does not sound as if you have a quality-minded contractor.
Also, how do you attach cement board to floor?
Precut and fit all the cement board and then lift all of the cement boards out. Then spread thinset mortar with the flat side of a 1/4-in. notched trowel and use the notched edge to “comb” the mortar. Embed the cement board and screw it to the underlayment with special 1-1/4 in.
What thickness cement board should I use?
Cement Board Thickness Cement backer board comes in two standard thicknesses, 1/2 inch and 1/4 inch. The industry standard is to use 1/2-inch-thick backer board on wall tile installations, such as a tub surround.
Which side of Hardibacker board goes down?
Cement board has a smooth side and a rough side. Face the rough side out if you will be using thin-set mortar adhesive to install the tile but the smooth side out if you will be using latex mastic.Can you use 1/4 inch cement board on floors?
Floors. Both 1/4- and1/2-inch cement board are appropriate for floors. To install cement board on floors, cement board manufacturers mandate a 5/8-inch plywood subfloor or OSB underlayment. They also require a 3/4-inch subfloor where tile size exceeds 12 inches.What is the difference between modified and unmodified thinset?
Unmodified thinset has been around forever. Unlike unmodified mortar, which consists only of a blend of Portland cement, sand, and water retention agents, modified thinset includes additional retention products, such as latex polymers, which can increase its performance and strength.Do you have to use Hardibacker under tile?
For tile, yes. If you aren't doing tile, no. Go with the hardie, well worth the extra money. the hardie backer install requires that if you are installing floor tile on it over a wood framed floor you need to spread a special mortar under the board.How thick should a subfloor be?
Typically made of plywood or OSB and ranging in thickness from 19/32" to 1 1/8" thick, the subfloor is truly structural, second only to joists in this respect. Subfloor holds up all of the above layers of flooring, as well as everything in your house—people, dogs, cats, pianos, furniture. All houses have subfloors.Do you have to use thinset under Hardibacker?
Since you are putting down hardie board on boards with small gaps, I would not recommend trying to put down thinset under it. It will make an enormous mess under the house (or whatever is under your bathroom). It is also more likely to make the floor uneven since it is hard to level thinset that is separated by gaps.Do I need plywood under cement board?
The Surface Below the Cement Board Flooring: For ceramic tile floors, the cement board usually rests on a plywood subfloor (minimum 5/8-inch-thick exterior-grade plywood or OSB). (Some cement board products may not require the underlying membrane if the seams are properly waterproofed.)Should you put cement board under a tub?
You don't need any cement board under the tub. It is far more important to have a sturdy layer of ply under the tub.What kind of Thinset do you use for Hardibacker?
To save a few bucks, you can use dry-set mortar under Hardi, but if you want to simplify things and deal with only one thinset, use a modified thinset like 253 Gold for both applications. Rialto is a porcelain tile that has deep depressions on the back.Do I need cement board under floor tile?
Cement board (used in tile underlayment) is now standard for most tile installations, but particularly for floor tile. Cement board also provides an additional layer over a plywood or particleboard subfloor, adding stiffness to the tiled surface to help prevent cracks.How do you secure backer board to floor?
Position each piece of backer board in the thin-set, press in place, and attach using special backer board screws on the spacing recommended by the backer board manufacturer. Cover the joints in the backer board with fiberglass tape embedded in thin-set adhesive and allow to set before tiling.How do you cut and install cement board?
Lay your cement board flat, and draw a line with a carpenter's pencil where you intend to cut. Then, place a straightedge along the line and drag either a drywall utility knife or a scoring tool against it. Repeat your cuts two to three times to make them deeper, which will make snapping the board easier.Can you walk on cement board?
You need to fasten the backer-board before the mortar sets up underneath, so walking on it while it's wet isn't a problem.How thick can Thinset be under tile?
The terms thinset cement, thinset mortar, dryset mortar, and drybond mortar are synonymous. This type of cement is designed to adhere well in a thin layer - typically not greater than 3/16th thick. For example, a 3/8" notch trowel will produce a 3/16th inch thick coating after the tiles are pressed in to the cement.How much thinset do you put under Hardibacker?
This is probably because at one time the installation instructions for Hardibacker called for 3/32" inch of thinset underneath. Currently, Hardibacker calls for either 1/4" thinset, or 5/32" mastic underneath. I always use 1/4" trowel for all my underlayment and 3/8" for almost all my tile.What happens if Thinset is too thin?
However, it does meet the minimum requirements of A118. 1 for unmodified thinsets, so, it should work. Since you mixed it too thin and spread it with the wrong trowel, it will take longer to set up. BUT, mixing it too thin also makes it weak.How long does cement board need to dry before tiling?
However, after you mount the backer board to the floor you simply have to seal the seams with mortar and wait until the mortar dries. This is normally 12 hours but may be up to 24 hours in some cases. After the mortar is dry the backer board is ready to receive the mortar for the tile. 
